lss: Refactor UART module to split out and share baud rate generation logic

Signed-off-by: Alex Forencich <alex@alexforencich.com>

rtl/lss/taxi_uart.f

@@ -1,4 +1,5 @@
 taxi_uart.sv
 taxi_uart_rx.sv
 taxi_uart_tx.sv
+taxi_uart_brg.sv
 ../axis/taxi_axis_if.sv

rtl/lss/taxi_uart.sv

@@ -51,6 +51,24 @@ module taxi_uart
 
 );
 
+wire baud_clk;
+
+taxi_uart_brg
+uart_brg_inst (
+    .clk(clk),
+    .rst(rst),
+
+    /*
+     * Baud rate pulse out
+     */
+    .baud_clk(baud_clk),
+
+    /*
+     * Configuration
+     */
+    .prescale(prescale)
+);
+
 taxi_uart_tx
 uart_tx_inst (
     .clk(clk),
@@ -72,9 +90,9 @@ uart_tx_inst (
     .busy(tx_busy),
 
     /*
-     * Configuration
+     * Baud rate pulse in
      */
-    .prescale(prescale)
+    .baud_clk(baud_clk)
 );
 
 taxi_uart_rx
@@ -100,9 +118,9 @@ uart_rx_inst (
     .frame_error(rx_frame_error),
 
     /*
-     * Configuration
+     * Baud rate pulse in
      */
-    .prescale(prescale)
+    .baud_clk(baud_clk)
 );
 
 endmodule

rtl/lss/taxi_uart_brg.sv

@@ -0,0 +1,57 @@
+// SPDX-License-Identifier: CERN-OHL-S-2.0
+/*
+
+Copyright (c) 2025 FPGA Ninja, LLC
+
+Authors:
+- Alex Forencich
+
+*/
+
+`resetall
+`timescale 1ns / 1ps
+`default_nettype none
+
+/*
+ * AXI4-Stream UART baud rate generator
+ */
+module taxi_uart_brg
+(
+    input  wire logic         clk,
+    input  wire logic         rst,
+
+    /*
+     * Baud rate pulse out
+     */
+    output wire logic         baud_clk,
+
+    /*
+     * Configuration
+     */
+    input  wire logic [15:0]  prescale
+);
+
+logic [15:0] prescale_reg = 0;
+logic baud_clk_reg = 1'b0;
+
+assign baud_clk = baud_clk_reg;
+
+always_ff @(posedge clk) begin
+    baud_clk_reg <= 1'b0;
+
+    if (prescale_reg != 0) begin
+        prescale_reg <= prescale_reg - 1;
+    end else begin
+        prescale_reg <= prescale - 1;
+        baud_clk_reg <= 1'b1;
+    end
+
+    if (rst) begin
+        prescale_reg <= 0;
+        baud_clk_reg <= 0;
+    end
+end
+
+endmodule
+
+`resetall

rtl/lss/taxi_uart_rx.sv

@@ -38,90 +38,99 @@ module taxi_uart_rx
     output wire logic  frame_error,
 
     /*
-     * Configuration
+     * Baud rate pulse in
      */
-    input  wire logic [15:0]  prescale
+    input  wire logic  baud_clk
 
 );
 
 localparam DATA_W = m_axis_rx.DATA_W;
 
 logic [DATA_W-1:0] m_axis_tdata_reg = 0;
-logic m_axis_tvalid_reg = 0;
+logic m_axis_tvalid_reg = 1'b0;
 
-logic rxd_reg = 1;
+logic rxd_reg = 1'b1;
 
-logic busy_reg = 0;
+logic overrun_error_reg = 1'b0;
-logic overrun_error_reg = 0;
+logic frame_error_reg = 1'b0;
-logic frame_error_reg = 0;
 
 logic [DATA_W-1:0] data_reg = 0;
-logic [18:0] prescale_reg = 0;
+logic [2:0] baud_cnt_reg = 0;
-logic [3:0] bit_cnt_reg = 0;
+logic run_reg = 1'b0;
+logic start_reg = 1'b0;
+logic stop_reg = 1'b0;
 
 assign m_axis_rx.tdata = m_axis_tdata_reg;
 assign m_axis_rx.tkeep = 1'b1;
 assign m_axis_rx.tstrb = m_axis_rx.tkeep;
 assign m_axis_rx.tvalid = m_axis_tvalid_reg;
 assign m_axis_rx.tlast = 1'b1;
+assign m_axis_rx.tid = '0;
+assign m_axis_rx.tdest = '0;
+assign m_axis_rx.tuser = '0;
 
-assign busy = busy_reg;
+assign busy = run_reg;
 assign overrun_error = overrun_error_reg;
 assign frame_error = frame_error_reg;
 
 always_ff @(posedge clk) begin
     rxd_reg <= rxd;
-    overrun_error_reg <= 0;
+    overrun_error_reg <= 1'b0;
-    frame_error_reg <= 0;
+    frame_error_reg <= 1'b0;
 
     if (m_axis_rx.tvalid && m_axis_rx.tready) begin
-        m_axis_tvalid_reg <= 0;
+        m_axis_tvalid_reg <= 1'b0;
     end
 
-    if (prescale_reg > 0) begin
+    if (!baud_clk) begin
-        prescale_reg <= prescale_reg - 1;
+        // wait
-    end else if (bit_cnt_reg > 0) begin
+    end else if (baud_cnt_reg != 0) begin
-        if (bit_cnt_reg > DATA_W+1) begin
+        baud_cnt_reg <= baud_cnt_reg - 1;
-            if (!rxd_reg) begin
+    end else if (run_reg) begin
-                bit_cnt_reg <= bit_cnt_reg - 1;
+        start_reg <= 1'b0;
-                prescale_reg <= {prescale, 3'd0}-1;
+        if (start_reg) begin
-            end else begin
+            // wait bit period for start bit
-                bit_cnt_reg <= 0;
+            baud_cnt_reg <= '1;
-                prescale_reg <= 0;
-            end
-        end else if (bit_cnt_reg > 1) begin
-            bit_cnt_reg <= bit_cnt_reg - 1;
-            prescale_reg <= {prescale, 3'd0}-1;
-            data_reg <= {rxd_reg, data_reg[DATA_W-1:1]};
-        end else if (bit_cnt_reg == 1) begin
-            bit_cnt_reg <= bit_cnt_reg - 1;
             if (rxd_reg) begin
+                // start bit high, clear run bit
+                run_reg <= 1'b0;
+                frame_error_reg <= 1'b1;
+            end
+        end else begin
+            {data_reg, stop_reg} <= {rxd_reg, data_reg};
+            if (stop_reg) begin
+                run_reg <= 1'b0;
+                if (rxd_reg) begin
+                    // stop bit high, transfer data
                     m_axis_tdata_reg <= data_reg;
-                m_axis_tvalid_reg <= 1;
+                    m_axis_tvalid_reg <= 1'b1;
                     overrun_error_reg <= m_axis_tvalid_reg;
                 end else begin
-                frame_error_reg <= 1;
+                    // stop bit low
+                    frame_error_reg <= 1'b1;
+                end
+            end else begin
+                baud_cnt_reg <= '1;
             end
         end
     end else begin
-        busy_reg <= 0;
+        data_reg <= {1'b1, {DATA_W-1{1'b0}}}; // marker bit
+        start_reg <= 1'b1;
+        stop_reg <= 1'b0;
         if (!rxd_reg) begin
-            prescale_reg <= {prescale, 2'd0}-2;
+            // falling edge of start bit
-            bit_cnt_reg <= DATA_W+2;
+            // wait half bit period
-            data_reg <= 0;
+            baud_cnt_reg <= 3'b011;
-            busy_reg <= 1;
+            run_reg <= 1'b1;
         end
     end
 
     if (rst) begin
-        m_axis_tdata_reg <= 0;
+        m_axis_tvalid_reg <= 1'b0;
-        m_axis_tvalid_reg <= 0;
+        rxd_reg <= 1'b1;
-        rxd_reg <= 1;
+        run_reg <= 1'b0;
-        prescale_reg <= 0;
+        overrun_error_reg <= 1'b0;
-        bit_cnt_reg <= 0;
+        frame_error_reg <= 1'b0;
-        busy_reg <= 0;
-        overrun_error_reg <= 0;
-        frame_error_reg <= 0;
     end
 end
 

rtl/lss/taxi_uart_tx.sv

@@ -36,21 +36,21 @@ module taxi_uart_tx
     output wire logic  busy,
 
     /*
-     * Configuration
+     * Baud rate pulse in
      */
-    input  wire logic [15:0]  prescale
+    input  wire logic  baud_clk
 );
 
 localparam DATA_W = s_axis_tx.DATA_W;
 
-logic s_axis_tready_reg = 0;
+logic s_axis_tready_reg = 1'b0;
 
-logic txd_reg = 1;
+logic txd_reg = 1'b1;
 
-logic busy_reg = 0;
+logic busy_reg = 1'b0;
 
 logic [DATA_W:0] data_reg = 0;
-logic [18:0] prescale_reg = 0;
+logic [2:0] baud_cnt_reg = 0;
 logic [3:0] bit_cnt_reg = 0;
 
 assign s_axis_tx.tready = s_axis_tready_reg;
@@ -60,39 +60,35 @@ assign txd = txd_reg;
 assign busy = busy_reg;
 
 always_ff @(posedge clk) begin
-    if (prescale_reg > 0) begin
+    s_axis_tready_reg <= 1'b0;
-        s_axis_tready_reg <= 0;
+
-        prescale_reg <= prescale_reg - 1;
+    if (!baud_clk) begin
+        // wait
+    end else if (baud_cnt_reg != 0) begin
+        baud_cnt_reg <= baud_cnt_reg - 1;
     end else if (bit_cnt_reg == 0) begin
-        s_axis_tready_reg <= 1;
+        busy_reg <= 1'b0;
-        busy_reg <= 0;
 
         if (s_axis_tx.tvalid) begin
-            s_axis_tready_reg <= !s_axis_tready_reg;
+            s_axis_tready_reg <= 1'b1;
-            prescale_reg <= {prescale, 3'd0}-1;
+            baud_cnt_reg <= '1;
             bit_cnt_reg <= DATA_W+1;
             data_reg <= {1'b1, s_axis_tx.tdata};
-            txd_reg <= 0;
+            txd_reg <= 1'b0;
-            busy_reg <= 1;
+            busy_reg <= 1'b1;
         end
     end else begin
-        if (bit_cnt_reg > 1) begin
-            bit_cnt_reg <= bit_cnt_reg - 1;
-            prescale_reg <= {prescale, 3'd0}-1;
         {data_reg, txd_reg} <= {1'b0, data_reg};
-        end else if (bit_cnt_reg == 1) begin
+        baud_cnt_reg <= '1;
         bit_cnt_reg <= bit_cnt_reg - 1;
-            prescale_reg <= {prescale, 3'd0}-1;
-            txd_reg <= 1;
-        end
     end
 
     if (rst) begin
-        s_axis_tready_reg <= 0;
+        s_axis_tready_reg <= 1'b0;
-        txd_reg <= 1;
+        txd_reg <= 1'b1;
-        prescale_reg <= 0;
+        baud_cnt_reg <= 0;
         bit_cnt_reg <= 0;
-        busy_reg <= 0;
+        busy_reg <= 1'b0;
     end
 end