Add irq status register

Upon receiving an interrupt, the corresponding bit in the interrupt
status register will be set and an IRQ will be raised for the CPU. The
cpu can then respond to the interrupt and clear the interrupt by writing
back to the interrupt status register.

hw/fpga/hvl/cs_testbench.sv

@@ -9,6 +9,7 @@ logic ram_cs;
 logic rom_cs;
 logic hex_cs;
 logic uart_cs;
+logic irq_cs;
 
 int cs_count = ram_cs + rom_cs + hex_cs + uart_cs;
 
@@ -32,11 +33,16 @@ initial begin : TEST_VECTORS
             else
                 $error("Bad CS! addr=%4x should have hex_cs!", addr);
         end
-        if (i >= 16'h7ff4 && i < 16'6) begin
+        if (i >= 16'h7ff4 && i < 16'h7ff6) begin
             assert(uart_cs == '1)
             else
                 $error("Bad CS! addr=%4x should have uart_cs!", addr);
         end
+        if (i == 16'h7fff) begin
+            assert(irq_cs == '1)
+            else
+                $error("Bad CS! addr=%4x should have irq_cs!", addr);
+        end
         if (i >= 2**15) begin
             assert(rom_cs == '1)
             else

hw/fpga/hvl/irq_testbench.sv

@@ -0,0 +1,75 @@
+module testbench();
+
+timeunit 10ns;
+
+timeprecision 1ns;
+
+logic clk_50, rst_n, button_1;
+logic [15:0] cpu_addr;
+wire [7:0] cpu_data;
+logic [7:0] cpu_data_in;
+logic [7:0] cpu_data_out;
+logic cpu_vpb, cpu_mlb, cpu_rwb, cpu_sync;
+logic cpu_led, cpu_resb, cpu_rdy, cpu_sob, cpu_irqb;
+logic cpu_phi2, cpu_be, cpu_nmib;
+logic [6:0] HEX0, HEX1, HEX2, HEX3, HEX4, HEX5;
+logic UART_RXD, UART_TXD;
+
+assign cpu_data = ~cpu_rwb ? cpu_data_out : 'z;
+assign cpu_data_in = cpu_data;
+
+super6502 dut(.*);
+
+always #1 clk_50 = clk_50 === 1'b0;
+always #100 dut.clk = dut.clk === 1'b0;
+
+always @(posedge dut.clk) begin
+    dut.cpu_phi2 <= ~dut.cpu_phi2;
+end
+
+logic [7:0] _tmp_data;
+
+initial begin
+    rst_n <= '0;
+    cpu_addr <= 16'h7fff;
+    cpu_rwb <= '1;
+    button_1 <= '1;
+
+    repeat(10) @(posedge dut.clk);
+    rst_n <= '1;
+
+    repeat(10) @(posedge dut.clk);
+    
+    button_1 <= '0;
+    @(posedge dut.clk);
+    button_1 <= '1;
+    @(posedge dut.clk);
+
+    assert(cpu_data[0] == '1)
+    else begin
+        $error("IRQ location should have bit 1 set!");
+    end
+
+    @(posedge dut.clk);
+    _tmp_data <= cpu_data_in;
+    @(posedge dut.clk);
+
+    _tmp_data <= _tmp_data & ~8'b1;
+
+    @(posedge dut.clk);
+
+    cpu_data_out <= _tmp_data;
+    cpu_rwb <= '0;
+
+    @(posedge dut.clk);
+
+    cpu_rwb <= '1;
+
+    repeat (5) @(posedge dut.clk);
+
+    $finish();
+    
+
+end
+
+endmodule